WHAT YOU DID TO YOUR TRUCK TODAY!

[JueOmega]

Ive got a spare check bar, remind me before Bala and Ill bring it along

It's ok drift, 10lb toffee hammer sorted it, All back together now
Thanks tho

[Drift]

[andysd1]

well i finally pulled my finger out and finished putting the rear Axel on, and treated her two a set of gas shocks,

now what to do, oh yer that

[yaki]

Chris I backed off those bolts, I just knew mine where going to snap and work was the next day, they are there to annoy me another day one thought, would they be easier to have gotten out with the engine warm?

Yep I had a funny feeling they were gonna but was in the kinda mood where I didn't care if they did cos i wanted it done, bad day at work

Had just got home so engine was warm, was working them back and fore to try an loosen them but didn't work

Taking the particulate filter off has made a slight difference to boost, it appears to come in slightly earlier and increases faster

[yaki]

Them bolts never come out first time. I did the same. Fortunately they arent a funny size and you can usually spin an M8 down a few and weld internally to turn them out.

You get yours out Ste? or still having a fight?

I dropped an M10 over them, wasn't much left poking up on the one and wanted to make sure I got enough penetration with the welder

[alex]

Nice one Chris, at least they do seem to trun out easy enough with a bit of heat from the welder.

[Drift]

Looks like Ive repaired the spare radiator, just off to fit it now

[Drift]

All fitted and sweet as a nut

Oh, the old rad

[Road Hog]

Well done bud see blue got in on the action

[alex]

Nice one.

I for one washed and waxed the 2.8 , I must be lucky or something because the gearsticks sit ok and there are no foul gears after the body lift. See show em some TLC and they respond like a lady

[andysd1]

well i jacked up livewires truck haha now taller than mine

[Livewire Frontera]

well i jacked up livewires truck haha now taller than mine

Show em the piccies son

Well impressed it now handles better too and i got back to southport and everywhere i go now everyone stops and stares at it

[yaki]

Nice one Chris, at least they do seem to trun out easy enough with a bit of heat from the welder.

Not sure if it was the heat from the welder, they were glowing after welding the nuts on, or the freeze spray I used

Welded nuts on stuff before after snapping them and it usually does the job, even done snapped off bleed nipples in brake calipers with no problems

[Dave_RAYNET]

All fitted and sweet as a nut

Oh, the old rad

now i ain't no expert..... but i'm pretty sure theres meant to be fins between them there strips....

[Drift]

Just a little worn out off roading

[alex]

Its Sunday, so thats all I'm doing.

viewtopic.php?f=46&t=23820&p=282383#p282383

[crabman]

Removed some badges , still , I have till Bala to remove all the sticky residue , lol .

[Trugga]

Removed some badges , still , I have till Bala to remove all the sticky residue , lol .

Use WD40

Lawrence

[Livewire Frontera]

Warm soapy water then polish off with T-cut it's how removed all the residue off mine but i used a hair dryer to remove the badges

[Trugga]

Installed fire extinguisher. Tightened the under tray bolts. Refitted tank guard. Pointed some stakes. Drilled holes and fitted rope handles to waffle boards. Electrical contact cleaned mirror switch. Created a pile of stuff in the middle of the garage that will be taken to Bala. Swapped road exhaust tail pipe for off-road one.

Having a break now, but will do a fluid check this afternoon.

Lawrence