WHAT YOU DID TO YOUR TRUCK TODAY!

[drinksoptional]

used thre lwb to shunt the sport out the drive turn it around then shunt it back in. And gave it a jump start and agian it fired into life never fails bit annoyed about battery drain though.

Any intresting bargain at the car booty

[Drift]

No, I was really good and didnt even look around
Made a ton but it was a bit quiet.

[drinksoptional]

Nice find hipo

[4x4 bobby]

I went to a car boot aswell and all i found was an Alchemist up to no good!!!!!!

[Drift]

[locospit]

Swapped the corroded back wheel for a spare we have knocking around in the shed on Julies Sport

Finally wired my spot lamps in.

[jellybaby]

replaced my brake pipes just get it retested tomorrow and a pass hopefully.

[locospit]

Nice looking motor Hipo.

Arden Blue ?

If they did a LWB in that colour I would have one.

[Loki]

Bought it and gave it a decent clean

[4x4 bobby]

Hi Loki. When you get a bit of time fill in your profile so if you ever have a question we can see what vehicle you have and where you are, that way you will get a quicker answer. Maybe not the right one but hey never mind eyh!!!!!!

Regards Bobster.

[fudge]

today i did a carboot and sold a few bits and one set of tyres that i got for £2 for £20
then tonight me and foggy finished off my front drive. by bolting on the drive sharft and filling the diff with oil. then bolting on the bach plates,

so i now have a working 4wd again

then me and foggy went out for a drive down a 3-4mile lane near us

[fogman]

& a good laugh it was

[andytats]

[fogman]

we will show it to you andy

[James Bass]

Out with Chel shopping today. Called into Maccy D's for lunch, and when I shut the engine off, the dreaded fuel cut off thingy that needs replacing (has since I bought her in January ) messed up again, and the engine over ran. ECU is now in limp mode once again. Not such a problem at the min though, as I'm not using her much with having a company car. Oh well.....will get it sorted eventually.

[drinksoptional]

you have no luck with that truck these days

I just secured a set of cobra bucket seat for a reasonible price off ebay

[James Bass]

Been fine for a while now Stu. Just one of those things that will keep cropping up until such time as I get the new switch fitted. Guess I'll have to find it first. lol.

[fudge]

today i receved my cambelt kit, will be doing that this weekend.
and then i took it our to test the front diff and all working
will put pic's up later


and my rear wheels are on flat ground

[RatCav]

Nice one Fudge ... you must of been drunk when you took the photo dude

[vauxsqueeks]

I used a 15+ year old MIG welder to seal up a small hole crack on my exhaust last night, at least that was the plan..

The welder although barely used in all this time seemed ok, with a new bottle of CO2 gas and a new feed tip. However may be I should have also changed the solder wire as this was a little dirty, gritty. After leaving about 1/4 inch of "bird crap" welding I burnt a half inch hole in the exhaust/muffler.

So re-adjusted the wire feeder and was all good, smooth delivery. Now I need a grinder to remove all the crap welding so I can re-seal the holes again.
Need to practice!

Saturday I am planning to do :

Front Brake Pads
Upper and Lower Ball Joints, NSF, OSF
Read Brake Pads
Grinding and re-Welding the exhaust
Hand brake adjustment, - one side is not working as well as the other..
Drain the Coolant, remove the radiator wash out the Welsh mud & re-fit.

It's going to be busy..