WHAT YOU DID TO YOUR TRUCK TODAY!

[weave67]

well after a day fitting geaboxes with erko and post finder i managed to get home and fit the ball joint and new gaiter and re adjust the bearing on the pass side on the dirty diesel

[Rich]

well done mate you will sleep tonight after all that hard work

[weave67]

well done mate you will sleep tonight after all that hard work

got one more job to do rich

[Rich]

is that why you were being nice to the misses on the phone

[JueOmega]

After all my grief with the engine on the 2.5 tractor, I took it for it's dreaded MOT, having not had the fronty long I had no real idea if there was anything likely to cause a failure. "IT PASSED" with a couple of advises so now, it's INSURED, MOT'D and TAXED, all ready for the meet on Sunday

[Rich]

well done mate

[gregster]

Made up some brackets to mount the truckman top properly on the chevy, repaired the tailgate locking rods and sourced a rear seal for the tailgate (landcruiser door rubber) as it was missing and hence the tailgate rattled.
Removed the chequer plate running boards as they are pointless, not strong enough to stand on and a pain to clean. and would get ripped of on something sooner or later.
These will be replaced by a set of jackable rocksliders that I will make shortly and weld directly to the chassis. (these might also be a mouting point for the external cage which is looking more likely )
Truck looks much taller with the running boards off
Measured up for the roof rack and started designing it...but will maybe do differently and incorporate into external cage,dunno yet...
Dug out a pair of lwb wings with arch extensions which will replace the dented chevy wings unless I come up with a o/s sport wing first as have a good sport n/s wing.
Dug out a sport bumper and lubed up all the bolts so I can get the end caps off another day.

[andysd1]

well i will fitting two of these,

well had a go at fitting these today, hahaha, took me just 4 hours to remove the top wish bone, now it looks like im going to have fun geting the old ones out

[Trugga]

well i will fitting two of these,

well had a go at fitting these today, hahaha, took me just 4 hours to remove the top wish bone, now it looks like im going to have fun geting the old ones out

A big press is required

Lawrence

[Road Hog]

Adjusted Hand brake then dug out my New Cap for the Eezibleed so far so good,fitted it on the reservoir



Found a handy place for the bottle



let the spare wheel down to the 20 psi working pressure as Gunsons recommend,connected the air to the bottle and



It is amazing how quick 1/2 litre blows out at that feeble pressure.

So any body wanting to use this system let the spare down to 5 psi & pull the rubber strap twice as tight as you are comfortable with

Bleed through whole brake system & clutch,then spent the remainder of the day washing the drive

[Frontycustoms]

Finally fitted my switch pod in & that was it for today.

[country_Est]

Not today but on Sat I did this
Went out with these



did a bit of this


and
Not my vids but from the bloke behind me
http://www.youtube.com/watch?v=3MAPbc5mr28

http://www.youtube.com/watch?v=b6HrHaaYJzY

[Sir-Doris]

Not to my truck by CheekyChicks... Changed a rear wheel bearing.

I called Weave a few days ago and asked him about The Bearinator, A friend, top bloke that he is went and got it from him as he had a few bits to do that way anyway and I collected it from A friend last Saturday. Well the bearing arrived tuesday and I decided I wanted a whole day set aside for it so started it today (Wed).

After me telling my dad how the Bearinator was specifically design for Frontera wheel bearings he took an interest and wanted to see how it worked.

I took all the gubbins off, caliper, disc, brake shoes etc and attached the monster slide hammer to the hub.

I thought I would take a little practice swing with it first just to get a feel for the slide action and imagine my surprise when the halfshaft came straight out and flew between my legs following the hammer.

Can I just say how DISAPPOINTED I was! I was expecting the veins in my temples to be popping out and beads of sweat to be running down my forehead and making my shirt stick to my back.

In all honesty though getting the old bearing off the halfshaft more then made up for the lack of hammer action and getting the new one on was a tedious process involving lots of tapping with a lump hammer to get the bearing and collar on properly.

All in all it still took a good few hours, what with tea stops and cigarettes and chatting to cheekychick and wandering into town for grinding discs and general faffing around. Not something I would like to do again in a hurry but all in all not as bad as I thought it was going to be.

Thanks very much Weave mate and A friend for FOG expressing it.

[cheekychick]

Thanks very much Weave mate and A friend for FOG expressing it.

Yeah, thanks guys, that was really nice of you

and of course BIG thanks to Sir-Doris again for everything he has done on my car(s), not just today

[andysd1]

well i will fitting two of these,

well had a go at fitting these today, hahaha, took me just 4 hours to remove the top wish bone, now it looks like im going to have fun geting the old ones out

A big press is required

Lawrence

have you got one

[Trugga]

...A big press is required

Lawrence

have you got one

Sorry, no - I used BikerBarney's at DTE in Kidderminster (well, he used it, I watched)

Lawrence

[Road Hog]

getting the new one on was a tedious process involving lots of tapping with a lump hammer to get the bearing and collar on properly
Thanks very much Weave mate and A friend for FOG expressing it.

[Road Hog]

Everybody seems to be missing a trick here......... The Bearinator is tubular why not put the new bearing on the shaft & tap it parallel,then put The Bearinator on the shaft upside down & use it as a DROP HAMMER,the weight of the slide will save an awful lot of your energy

Also you are both very welcome although it is a real strain sitting over Dave`s drinking tea & shooting the breeze

[Adam]

completed the extra wireing for all the lights and removed the old vauxhall badge on the grill and fitted a old style vauxhall name plate, i think it looks a lot better will post a pick of it soon so you can all take the p+ss

[cheekychick]

I think that the tube needs to be a bit wider, we did think of that, and thought it might be a good idea for mk2 that and there are welds on that end from the Alex/Dave improv when they had to use it to get a bearing out that had stayed attached to the car .

But hey, it is all done now fingers crossed he doesn't need anything else for his MOT

Glad it gave you a reason for more tea drinking A friend